Home Care Library
Water Heater (electric)
Flush out sediments, and test pressure relief valve
Relief valve testing: The pressure relief valve is an important safety feature of your water heater.If too much pressure builds up on the tank, the pressure relief valve opens up to relieve the pressure.However, corrosion or scale build-up can prevent the valve from operating properly, potentially resulting in the tank exploding.Therefore it is very important to test the pressure relief valve to ensure that it is operating properly.
|Every 4 months: March, September, December (yearly)|
NOTE: The tasks and timings shown here for your Water Heater (electric) are based on a single-family home (owned), located in Massachusetts, United States, with priority set at ‘1 star' or higher, for all possible goals.
If you set your personalization differently in your Home Wizard app, then you may get reminders for different tasks and timings in your recommended home care program for your Water Heater (electric).
FLUSH OUT SEDIMENTS: On the side of the hot water heater, on the lower part of the tank, is a valve for draining water out of the tank of the hot water heater. Draining water out of the tank flushes out sediments that settle to the bottom of the tank as the water is heated.
To flush the tank:
For electrical water heaters, turn OFF the power at the circuit breaker. And for gas models, turn the thermostat on the unit to the PILOT position.
Connect a garden hose to the drain valve at the bottom of the tank, and put the other end either in a 5-gallon bucket, a floor drain, or run the hose outside.
If you have a recirculation pump for your hot water system, then turn this off.
Shut off the supply valve for the cold water inlet to the water heater.
Open a HOT water faucet in a sink closest to your water heater, and open another HOT water faucet in a sink that is at the highest point in your house (NOTE: Just a little water will flow out, since you have shut the water supply valve to your hot water heater in the step above).
Open the pressure relief valve at the top of the tank (you might want to place a rag or small bowl under the vent pipe to catch any water drops that might come out).
Open the drain valve on you tank and drain 1 to 2 gallons from the tank. NOTE: The water coming out of the garden hose will be scalding hot so be careful that the water doesn't splash anywhere except in the bucket, drain, or outside. As the water begins to drain out, you will probably notice some small scale or sediment in the water.
To re-fill the tank:
Close the drain valve and remove the garden hose.
Close the pressure relief valve at the top of the tank.
Open the valve for the cold water inlet to the tank, and you should start to hear the tank fill with water.
Watch the faucets that you opened in the house. After you begin to get a steady stream of water from the faucet, shut that faucet.
For electric water heaters, turn the power back on, and for gas models, turn the thermostat on the water heater back to its ON position.
If you have a recirculation pump, then turn it back on.
Double check that the drain valve is tight.
TEST PRESSURE RELIEF VALVE: The pressure relief valve is at the top of the tank, with a drain tube extending down from it.
To test the valve, with the water supply valve to your water heater in the open position (i.e., its normal operating position), place a bucket under the vent pipe for the valve, then lift the lever on the valve for a few seconds to let water flush out through the valve.
If little or no water flows out, or if the valve doesn't shut off, then replace it.
NOTE: The water coming out of the vent pipe will be scalding hot, so be careful that the water doesn't splash on you.
Health & Safety
Avoiding Unscheduled Repairs
The benefits of this task are moderately high, as doing this task will help extend the useful life of your water heater, which is a relatively expensive piece of equipment in your home. This task also helps save you energy by maintaining the efficiency of your water heater. Testing the relief valve helps insure safe operations of your unit.
The cost of this task is moderately high from an investment of time standpoint. It is estimated that this task should take about 60 minutes to complete. You will need a hose and bucket to do this task.
Other Routine Care Tasks